Tuesday, December 3, 2013

How To Make A DIY Outdoor Zinc Table

$250 homemade zinc table.

With a new deck, B quickly started designing ideas for filling the space. First on the wish list was an outdoor table. Being someone who likes low maintenance solutions, I told her to find a solution that uses metal instead of wood for the tabletop.

We landed on copper initially, but it was too expensive and I'd worry too much about it being stolen. Second in line was zinc - rustproof and easy to age with the right chemicals.

We didn't want to break the bank with a high end purchase, so we opted to try and make something on our own instead of something like this that costs upwards of $1k. I've never made a big table before, so I did a little research and reverse engineered the table in our dining room for ideas.


Below is the photo documentation of my process, enjoy!


Big heavy door I found at Restore, only $10! I'm marking where I want my legs to go (2.5" from outer edge).

The door was laminated in walnut - hard not to stain it and use it inside somewhere.
Big sheet of zinc, probably weighed 50lbs.

This sheet had some dings in it, so they took off $75 dollars.

Basically, you figure out where your legs go, and build supports to hold the legs.

The 45º piece secure the trim work and lets you bolt the legs to the table.
Notching the legs 3.5" so it can butt up to the 45º wood support

Bolted trim to table leg.

You can see how it comes together here.

Now for the flip. Good proportions between table thickness and legs and trim work.
Detail of uncovered table. This could be done if it was for inside.

Adding construction adhesive to the table with adhesive spreader.


Laying the table down after glue.

Then put everything heavy in the house on top.

Flipped the table, started bending with mallet and then started making cuts with snips


Lots of hammering and patience.

45º cuts to let the corners play nicely.

Nailed the zinc to the table.


Added some foil tape to remove the sharpness under the table. Finger protection.

Took the table outside and screwed back on the legs. Next time I would mark which leg goes where so I don't have to guess. I soldered the corner joints with some basic tin solder and grinded them smooth.

We used a mallet and pounded on the table top for a nice texture. Probably hammered for a few hours for a look we were happy with.
Now the fun part, we misted on some copper sulfate and got this cool patina. Doesn't take a lot of copper sulfate for good results. If you put on too much, you can scrub it clean with fine steel wool.


The patina takes it to a new level.


Still shiny at the right angle.


Project Costs:
Tabletop: 7' x 3' x 1.5" Solid core door from Habitat Restore ($10)
Legs = 30" Cedar 4" x 4" posts from Lowes ($30)
Trim work = 1" x 4" cedar planks from Lowes ($15)
Zinc Sheet Metal = 9' x 4' from Rotometals ($120)
Liquid Nails = 6 tubes ($25) from Lowes
Bolts and Nails = 8 - 4" bolts, galvanized box nails ($10) from Lowes
Copper Sulfate = 1 lb from Amazon.com ($5)



Wednesday, November 20, 2013

Building a Low Ground Cedar Deck

Our backyard was in shambles when we got this house 5 years ago.

Bit by by bit, we've been improving things, working from the back of the yard, towards the house.

Before we started on the deck, I had a company bury our electrical and internet lines to the house. It costs to have the company bore the tunnel, but not trenching was really nice, and it also saved the lawn.

Now to the deck.

We elected for cedar. Mostly because it handles the outdoors well while being a pleasant softwood material. I like how it feels barefoot, it smells great, and its just a fun wood to work with.

My biggest goals were to have it be simple, seamless and straight. One of those decks that sorta blends into the larger landscape and is easy to access from multiple points.

I had to keep the deck low to the ground for privacy reasons. Since our street is sloped, its pretty easy to see into the neighbors yards. This low-to-the-ground detail presented some challenges that required alot of digging and workarounds.

Electrical now connects from back of garage to pole, shooting underground to house.

Looking out from the backdoor, you can see post holes and some trenches for the beams.

Looking towards the house from back of yard, notice the concrete steps to the house.

Lots of strings helped me visualize the size of the deck and where to dig holes for posts.

Once I was ready, I poured water into the hole and added concrete, stirred with a compost mixer.

Don't use twine for strings, as they quickly lose their tension and/or break. Use the pink mason string.

Progress with a few posts and metal fixtures attached.

All the posts supports poured and ready.

I had to level the stoop's last step as it was going to support the decking. This also told me how low I could get to the ground.

I started laying beams with the corner that required the most digging and worked my way out.



Framing around fence and stoop. There was lots of improvising working around the old stairs.

I added gravel when the wood was close to the ground.

Framing and joists done, now to the decking - the fun part.

The trick to straight planks is starting with a good straight end piece and being patient. Each piece has a slight bow, so you need to pull and push ever so slightly to stay even across the deck. We used a wonderbar and a long wood clamp to pull the decking together when necessary.

Instagram version of deck.
Decking added with dog and wife to test. Lots of extra dirt helped us grade our yard.

I used the "camo nailer" to hide our decking screws, and 18' planks so we didn't have any seams. I think they are liking the deck.

Remember the concrete stoop? We built on top of it.


I stained the deck with Penofin in their "Sierra" color. It also matches our fence.

After looking at some options, we decided to paint the risers with Sherwin Williams Duration Creamy White for contrast.

We moved our park bench to the top of the hill to break up the empty space out there. We painted it to match the Walnut tree leaves in October.

Cedar fascia boards were added around the perimeter of the deck for a clean look. Sod added too.

Wednesday, September 11, 2013

Blue Never Felt So Good


Pardon my melodramatic writing for this one post.

We started painting this old house 24 months ago. It started during our kitchen remodel. Painting was something cheap that we did to keep us busy while we watched the contractors work inside. Since then, we've been chipping away at the project, side by side. Each side took about 3-6 months to complete. Winters and summers also slowed us down.

One added detail to the painting project - I also decided to refinish/replace each shingle before the paint. Anyone can paint a house, but most aren't willing to go to the trouble to scrape, refinish and caulk every nook and cranny.

This year we finished the south wall, and in a rush to finish the front of the house, I elected to hire a contractor to replace all the old shingles with new.

I would say this was the most difficult and physically demanding project we've taken on. I went through 4 orbital sanders, 14 boxes of shingles, 50 tubes of caulk, and thousands of sanding pads.

We're happy with the results, and more happy to say we're done! Enjoy.

The carpenters started on the left edge and worked to the right, bottom to top, sections at a time.

Carpenter's progress at end of day 2. We had to buy 11 boxes of shingles for the front.

Completed shingles before paint. I stripped the window trim and fascia boards after they left.

This type of project definitely requires a helper. The porch roof really helped them out with easy access.

Pregnant wife helping me out with painting. Worst husband or best wife ever? 

Painting done, with a lovely lady at the door.

Kinda looks like a ship at this angle.



A month before we bought the house.

4.5 years later.
Before/after.

Monday, August 26, 2013

Baby Room Book Ledge

Red oak book ledge with some of our favorites on display

B suggested we make a book ledge in the baby room that goes across the long wall. Thankfully, with a bunch of old oak left over from our kitchen remodel, I can make these in a matter of a few hours.

The vertical trim piece of a doorway is almost perfect for this type of project. I ripped the piece so it's about 3" wide, and nailed on smaller strips on the back and front ledge to create a channel for the books.

We debated on painting it white, but B elected for the dark wood stain.

Installing requires locating a stud, so we ended up drilling a bunch of tiny holes behind the ledge until we hit something solid (the joys of plaster and lathe).

I think we may add another eventually, but for now, I like the simplicity of one long shelf across the room.




Should hold books until the kid tries to climb the wall with shelf.

You can see where we made some pencil marks for alignment

Monday, August 19, 2013

$20 Antique Door - Score!

A few weeks ago I went to Habitat ReStore in Kansas City for fun on a lunch break. I joke that casual trips to ReStore are "dangerous" because you will walk into the store with no intentions of buying and leave with an unplanned weekend project.

My last trip was a classic example. We quickly stumbled upon a pile of $20 two panel closet doors that perfectly match our house's style. I reluctantly texted B a picture (below), knowing this would pique her interest.



Fast forward 4 hours later, and we're rushing across town in our van to buy three of these doors for our upstairs closets. We could have bought more, but since these all required stripping and refinishing to match our house, I didn't want overcommit to stripping (see exterior house project).

Well, once I got to "stripping," things got really messy. I'll spare you the pictures, but it did take an entire bottle of this stuff to get about 6 layers of white paint off the doors.



The exciting/scary part of doing this is that you have no idea what wood type and finish you'll be left with. I was afraid it would be cheap pine and be a total waste of time. Thankfully, the wood was beautiful and stained up perfectly!

Total time was about 12 hours. I spent about an hour every weeknight for two weeks, and then finally hung the door this weekend.

Here's the skinny 24" closet door in all its restored glory

We kept the original doorknob and spray painted it oil rubbed bronze

The doors ended up being a beautiful pine. I love the thin grain on the frame. Also, we cut out the original panel trim and replaced them with a simple shaker style trim. This saved loads of stripping time.


I absolutely love the idea of restoring old things - the only risk is that sometimes you'll end up spending ridiculous amounts of time and $ to restore that cheap item you found. With this project, I probably spent $50 on this door, including some new materials, like trim, bondo, and fixing some door jamb hardware. The time was a little bit much, but it quickly became a labor of love, so I have no regrets (yet).

New doors like this cost about $240 each, so I think we did ok.

And just for reference, here's the before/after pic.





Tuesday, July 30, 2013

Painting Progress: Three Sides Done

Look what we finished this weekend . . . .


Current painting status is three sides done, as well as the front porch - leaving just the front 2nd and 3rd stories to sand and paint. I'm starting to believe this project might actually end some day . . . .

twitter test