Tuesday, December 3, 2013

How To Make A DIY Outdoor Zinc Table

$250 homemade zinc table.

With a new deck, B quickly started designing ideas for filling the space. First on the wish list was an outdoor table. Being someone who likes low maintenance solutions, I told her to find a solution that uses metal instead of wood for the tabletop.

We landed on copper initially, but it was too expensive and I'd worry too much about it being stolen. Second in line was zinc - rustproof and easy to age with the right chemicals.

We didn't want to break the bank with a high end purchase, so we opted to try and make something on our own instead of something like this that costs upwards of $1k. I've never made a big table before, so I did a little research and reverse engineered the table in our dining room for ideas.


Below is the photo documentation of my process, enjoy!


Big heavy door I found at Restore, only $10! I'm marking where I want my legs to go (2.5" from outer edge).

The door was laminated in walnut - hard not to stain it and use it inside somewhere.
Big sheet of zinc, probably weighed 50lbs.

This sheet had some dings in it, so they took off $75 dollars.

Basically, you figure out where your legs go, and build supports to hold the legs.

The 45º piece secure the trim work and lets you bolt the legs to the table.
Notching the legs 3.5" so it can butt up to the 45º wood support

Bolted trim to table leg.

You can see how it comes together here.

Now for the flip. Good proportions between table thickness and legs and trim work.
Detail of uncovered table. This could be done if it was for inside.

Adding construction adhesive to the table with adhesive spreader.


Laying the table down after glue.

Then put everything heavy in the house on top.

Flipped the table, started bending with mallet and then started making cuts with snips


Lots of hammering and patience.

45º cuts to let the corners play nicely.

Nailed the zinc to the table.


Added some foil tape to remove the sharpness under the table. Finger protection.

Took the table outside and screwed back on the legs. Next time I would mark which leg goes where so I don't have to guess. I soldered the corner joints with some basic tin solder and grinded them smooth.

We used a mallet and pounded on the table top for a nice texture. Probably hammered for a few hours for a look we were happy with.
Now the fun part, we misted on some copper sulfate and got this cool patina. Doesn't take a lot of copper sulfate for good results. If you put on too much, you can scrub it clean with fine steel wool.


The patina takes it to a new level.


Still shiny at the right angle.


Project Costs:
Tabletop: 7' x 3' x 1.5" Solid core door from Habitat Restore ($10)
Legs = 30" Cedar 4" x 4" posts from Lowes ($30)
Trim work = 1" x 4" cedar planks from Lowes ($15)
Zinc Sheet Metal = 9' x 4' from Rotometals ($120)
Liquid Nails = 6 tubes ($25) from Lowes
Bolts and Nails = 8 - 4" bolts, galvanized box nails ($10) from Lowes
Copper Sulfate = 1 lb from Amazon.com ($5)



9 comments:

  1. Replies
    1. Thanks @kcmaria. We itching to break it in this spring.

      Delete
    2. How did you get your table to have the nice shine? After we applied the Copper Sulfate it is pretty dull, cool but dull. I would like to achieve the finish you have. Thanks!

      Delete
    3. Hi Alice. The shine on our table has gone away since we added the copper sulfate, and we find we prefer it that way. The shine caught a lot of sunshine, giving us a mean glare depending on where the sun was, and the rustic look of the dull finish is much more forgiving in terms of dings and bumps. We'll try to post an updated photo soon so you can see how it is aging.

      Delete
  2. Wow! Your ideas are awesome: from the low-maintenance metal tabletop to actually using a door as a table! I wouldn’t think you used those materials, and I’m sure they’re very cost-efficient. And I agree that metal tops are better when it comes to cleaning and maintaining than wood. They got that smooth surface devoid of wood’s scratchy surface. Anyways, thanks for sharing these great idea. Cheers!


    Marion Dunn @ Global Resources

    ReplyDelete
  3. I love the idea of using other tables to hold it down while the glue is curing. Great table!

    ReplyDelete
  4. Love the table, does it get hot to the touch in the sun?

    ReplyDelete
  5. I've shopped at Multiwood for years, and their consistent quality and service keep me coming back. It's rare to find a furniture store that checks all the boxes like they do

    For more detail: https://multiwood.ae/

    ReplyDelete

twitter test